Service instructions for JA-110R
Radio Module
This product is a component of the JABLOTRON JA-100 alarm system. It enables wireless communication with wireless Jablotron 100 series components. Because of the expansion of the coverage area, up to three JA-110R modules can be used in the system. The product is intended to be installed by a trained technician with a valid Jablotron certificate.
Installation
The module can either be installed directly in the cover of the control center cabinet, or it can be placed in a suitable location in the house. Do not place the module near larger metal objects, also not near installations or pipes that could negatively affect wireless communication.
Figure:1 - snap terminal of the screen; 2 - yellow signal light of interference; 3 - red signal light of communication
1. Open the screen (by pressing the snap clip 1).
2. If the module is installed in the cover of the control center, screw on the plastic back panel as shown.
Illustration: installation of the module in the cover of the central controller.
3. If installing on a wall in the house, prepare the supply of the BUS cable and mount the back panel at the chosen location (a vertical orientation is recommended).
Before connecting the BUS, the system must be disconnected from the power supply.
4. Connect the BUS cable to the terminals (the cable must not enter the antenna area when the screen is closed). If the module is installed in the cover of the control unit, connect the BUS via a cable through to the connectors.
The flat cable with RJ connectors may only be used for connecting the BUS up to a maximum length of 3 m.
5. Continue to follow the installation instructions of the central unit. Basic steps:
a. After power on, the yellow signal light (2) flashes because the module has not been read into the system.
b. Select the required position in the F-Link program on the peripheral devices card and start the learning mode with the Read button.
c. Press the tamper switch in the module (6) - causing the module to learn and the yellow light will extinguish.
6. Close the cover of the module.
Figure: 4 - antenna; 5 - serial number; 6 - sabotage switch; 7 - terminals of the BUS; 8 - connector of the BUS; 9 - cable with connectors (installation in the cover of the control unit);
Setting properties of the module
This is done by the F-Link program - card Peripheral devices. On the position of the module Use Internal setting. A dialog appears, where the following properties can be set:
LED indication at communication: from the factory it is set that at operation the module indicates communication with a wireless peripheral with the red signal light. You can disable this indication.
Failure detection: from the factory is off. However, it can be set to two levels - low (interference lasts longer than 30s over the course of a minute) and high (interference lasts longer than 10s for 20s). When detection is enabled, the system is able to report the communication band interference.
Learning signal: by using this selection in the program, the module sends a learning signal (intended for wireless peripherals, which contain only one receiver).
Technical parameters
Power supply from the BUS of the central unit 12 V (9...15 V)
Current consumption on standby (idle) 25 mA
Current consumption for cable selection 25 mA
Radio communication 868.1 MHz
Dimensions 150 x 40 x 23 mm
Classification grade 2
In accordance with CSN EN 50131-1, CSN EN 50131-3, CSN EN 50131-5-3
Environment in accordance with CSN EN 50131-1 II. indoors, general
Operating temperature range -10 to +40°C
Further complies with CSN ETSI EN 300220, CSN EN 50130-4,
CSN EN 55022, CSN EN 60950-1
Conditions of operation CTÚ VO-R/10/06.2009-9
Product is designed and manufactured in accordance with the provisions to be applied to it: Government Decree No. 426/2000 Sb. if used according to its intended use.
Remark: Although this product does not contain harmful materials, do not dispose of it in the domestic waste, but dispose of it at the collection point intended for electronic waste.
Installation
The module can either be installed directly in the cover of the control center cabinet, or it can be placed in a suitable location in the house. Do not place the module near larger metal objects, also not near installations or pipes that could negatively affect wireless communication.
Figure:1 - snap terminal of the screen; 2 - yellow signal light of interference; 3 - red signal light of communication
1. Open the screen (by pressing the snap clip 1).
2. If the module is installed in the cover of the control center, screw on the plastic back panel as shown.
Illustration: installation of the module in the cover of the central controller.
3. If installing on a wall in the house, prepare the supply of the BUS cable and mount the back panel at the chosen location (a vertical orientation is recommended).
Before connecting the BUS, the system must be disconnected from the power supply.
4. Connect the BUS cable to the terminals (the cable must not enter the antenna area when the screen is closed). If the module is installed in the cover of the control unit, connect the BUS via a cable through to the connectors.
The flat cable with RJ connectors may only be used for connecting the BUS up to a maximum length of 3 m.
5. Continue to follow the installation instructions of the central unit. Basic steps:
a. After power on, the yellow signal light (2) flashes because the module has not been read into the system.
b. Select the required position in the F-Link program on the peripheral devices card and start the learning mode with the Read button.
c. Press the tamper switch in the module (6) - causing the module to learn and the yellow light will extinguish.
6. Close the cover of the module.
Figure: 4 - antenna; 5 - serial number; 6 - sabotage switch; 7 - terminals of the BUS; 8 - connector of the BUS; 9 - cable with connectors (installation in the cover of the control unit);
Setting properties of the module
This is done by the F-Link program - card Peripheral devices. On the position of the module Use Internal setting. A dialog appears, where the following properties can be set:
LED indication at communication: from the factory it is set that at operation the module indicates communication with a wireless peripheral with the red signal light. You can disable this indication.
Failure detection: from the factory is off. However, it can be set to two levels - low (interference lasts longer than 30s over the course of a minute) and high (interference lasts longer than 10s for 20s). When detection is enabled, the system is able to report the communication band interference.
Learning signal: by using this selection in the program, the module sends a learning signal (intended for wireless peripherals, which contain only one receiver).
Technical parameters
Power supply from the BUS of the central unit 12 V (9...15 V)
Current consumption on standby (idle) 25 mA
Current consumption for cable selection 25 mA
Radio communication 868.1 MHz
Dimensions 150 x 40 x 23 mm
Classification grade 2
In accordance with CSN EN 50131-1, CSN EN 50131-3, CSN EN 50131-5-3
Environment in accordance with CSN EN 50131-1 II. indoors, general
Operating temperature range -10 to +40°C
Further complies with CSN ETSI EN 300220, CSN EN 50130-4,
CSN EN 55022, CSN EN 60950-1
Conditions of operation CTÚ VO-R/10/06.2009-9
Product is designed and manufactured in accordance with the provisions to be applied to it: Government Decree No. 426/2000 Sb. if used according to its intended use.
Remark: Although this product does not contain harmful materials, do not dispose of it in the domestic waste, but dispose of it at the collection point intended for electronic waste.