Service instructions for JA-114E
Wired code control panel with RFID and LCD Display
The control panel is a component of the JABLOTRON JA-100 alarm system. Thanks to the simple system, it is possible to put together a configuration tailored to installation size and user requirements. The product should be installed by a trained technician with a valid Jablotron certificate.
The control panel includes a display, RFID reader and the 1st control segment (1). This configuration can be expanded with the desired number of JA-192E segments (up to max. 20 per configuration). The hinged cover of the panel (6) can be disassembled if desired, to provide permanent access. The panel also works as a reader of contactless access cards / tags (RFID).
Illustration: 1 - control segment; 2 - segment keys; 3 - module control panel; 4 - illuminated activation key; 5 - terminals for opening; 6 - screws of cover;
Figure: 7 - audio module connector; 8 - control segment connector; 9 - serial number; 10 - bus connection terminal; 11 - connection terminal for interconnection of audio module with the control panel, 12 - tamper switch;
Installation
1. Successively press the four terminals on sides (see Fig. 1) and detach the control panel from the plastic back panel.
2. When installing the next control segment, first remove the sealing cap at the top of the 1st segment.
3. Remove the transparent covers from segments (by pulling forcefully on both sides at segment keys).
4. Always connect the guide wires of the segment to the connector of the previous segment and snap them together (it is best to always rotate the guide wires, turning the segment by 360° - that way the wires do not accidentally get caught between the plastic parts). Install all desired control segments in the same way. Finally, replace (click in) the sealing cap.
5. Pull the cable through the plastic back panel and screw on the back panel with segments at the selected location. When using several operating segments, also secure the segments against the wall (choose the number of screws as required).
6. Connect bus cable to the connection terminal (11).
Before connecting the BUS, the system must be disconnected from the power supply.
7. Connect supply for segments to the internal connector of the control panel (8).
8. Snap the control panel into the configuration.
9. Continue to follow the manual for installation of the control panel. Basic steps:
a. After power on, the yellow signal light flashes because the control panel is not assigned to the system.
b. Select the desired position in the F-Link program on the Peripheral Devices card and start the learning mode with the Read button.
c. Press the illuminated activation key (4), which causes the control panel to learn and the yellow light will extinguish.
10. After assembly is complete, insert description labels into the segment covers and close the covers. Description labels are printed as part of the F-Link program (Peripheral devices card, at control panel position - Internal setting).
Illustration: insert description label in the control segment.
Set properties
This is done by the F-Link program - card Peripheral devices. On position of the control panel Use Internal setting. The present configuration appears, with possibility of setting its properties. Individual segments can be assigned the desired functions (operation sections, signaling state of sections, alarm striking, operation PG output, signaling state PG output, etc.). Details can be found in the F-Link program.
Change configuration
If the configuration of segments needs to be changed, pull them apart at the joint location, on the sides (on the side of the keys).
Technical parameters
Power supply from central controller bus (9...15 V)
Current consumption in standby (idle) 15 mA
Current consumption for cable selection 50 mA
Each added operating segment 0.5mA
RFID frequency 125kHz
Operating temperature range -10 to +40 °C
Environment according to CSN EN 50131-1 II. indoors, general
Classification grade 2
In accordance with CSN EN 50131-1, CSN EN 50131-3,
Further complies with CSN ETSI EN 300330, CSN EN 50130-4,
CSN EN 55022, EN 60950-1
Conditions of operation CTÚ No. VO-R/10/09.2010-11
Product is designed and manufactured in accordance with the provisions to be applied to it: Government Decree No. 426/2000 Sb. in the text of subsequently promulgated regulations, if used according to its intended use.
Remark: Although this product does not contain harmful materials, do not dispose of it in the domestic waste, but dispose of it at the collection point intended for electronic waste.
The control panel includes a display, RFID reader and the 1st control segment (1). This configuration can be expanded with the desired number of JA-192E segments (up to max. 20 per configuration). The hinged cover of the panel (6) can be disassembled if desired, to provide permanent access. The panel also works as a reader of contactless access cards / tags (RFID).
Illustration: 1 - control segment; 2 - segment keys; 3 - module control panel; 4 - illuminated activation key; 5 - terminals for opening; 6 - screws of cover;
Figure: 7 - audio module connector; 8 - control segment connector; 9 - serial number; 10 - bus connection terminal; 11 - connection terminal for interconnection of audio module with the control panel, 12 - tamper switch;
Installation
1. Successively press the four terminals on sides (see Fig. 1) and detach the control panel from the plastic back panel.
2. When installing the next control segment, first remove the sealing cap at the top of the 1st segment.
3. Remove the transparent covers from segments (by pulling forcefully on both sides at segment keys).
4. Always connect the guide wires of the segment to the connector of the previous segment and snap them together (it is best to always rotate the guide wires, turning the segment by 360° - that way the wires do not accidentally get caught between the plastic parts). Install all desired control segments in the same way. Finally, replace (click in) the sealing cap.
5. Pull the cable through the plastic back panel and screw on the back panel with segments at the selected location. When using several operating segments, also secure the segments against the wall (choose the number of screws as required).
6. Connect bus cable to the connection terminal (11).
Before connecting the BUS, the system must be disconnected from the power supply.
7. Connect supply for segments to the internal connector of the control panel (8).
8. Snap the control panel into the configuration.
9. Continue to follow the manual for installation of the control panel. Basic steps:
a. After power on, the yellow signal light flashes because the control panel is not assigned to the system.
b. Select the desired position in the F-Link program on the Peripheral Devices card and start the learning mode with the Read button.
c. Press the illuminated activation key (4), which causes the control panel to learn and the yellow light will extinguish.
10. After assembly is complete, insert description labels into the segment covers and close the covers. Description labels are printed as part of the F-Link program (Peripheral devices card, at control panel position - Internal setting).
Illustration: insert description label in the control segment.
Set properties
This is done by the F-Link program - card Peripheral devices. On position of the control panel Use Internal setting. The present configuration appears, with possibility of setting its properties. Individual segments can be assigned the desired functions (operation sections, signaling state of sections, alarm striking, operation PG output, signaling state PG output, etc.). Details can be found in the F-Link program.
Change configuration
If the configuration of segments needs to be changed, pull them apart at the joint location, on the sides (on the side of the keys).
Technical parameters
Power supply from central controller bus (9...15 V)
Current consumption in standby (idle) 15 mA
Current consumption for cable selection 50 mA
Each added operating segment 0.5mA
RFID frequency 125kHz
Operating temperature range -10 to +40 °C
Environment according to CSN EN 50131-1 II. indoors, general
Classification grade 2
In accordance with CSN EN 50131-1, CSN EN 50131-3,
Further complies with CSN ETSI EN 300330, CSN EN 50130-4,
CSN EN 55022, EN 60950-1
Conditions of operation CTÚ No. VO-R/10/09.2010-11
Product is designed and manufactured in accordance with the provisions to be applied to it: Government Decree No. 426/2000 Sb. in the text of subsequently promulgated regulations, if used according to its intended use.
Remark: Although this product does not contain harmful materials, do not dispose of it in the domestic waste, but dispose of it at the collection point intended for electronic waste.