dahua
-
Dahua VTNS2003B Two-wire switch
Dahua VTNS2003B-2 Two wire switch The VTNS2003B-2 is a switch for products from the new generation of Dahua Video Intercom products. The communication of this generation of video intercom products uses the SIP protocol. This protocol ensures a good speech-listening connection and offers possibilities for integration with third parties. The 2-wire technology simplifies installation and offers the possibility of connecting multiple op stations to a single cable. Plus points: Multiple devices on one 2-wire connection: It is possible with this generation to serialize multiple products from each other via the "out" port. The switches can also be connected to each other via 2 wires. However, each switch must be supplied with 48VDC separately. 2-wires for one system: Both the power supply for the indoor and outdoor stations and the data transmission goes through the same cable. This allows the stations to be placed on the same line, making 2 wires sufficient for a working system. TCP-IP network protocol: Despite the 2-wire technology, the posts just work as regular network products. This means that each post needs to have its own unique IP address. A big advantage of this is that posts connected to the this 2-wire switch can be combined with the PoE products and the 2-wire products from the previous generation. Suitable for DMSS and DSS Pro: Because the 2-wire products are simply part of the network, they can also be applied with the DMSS app or DSS Pro management software Points of interest: Not suitable for all 2-wire products: This switch is not suitable for all Dahua 2-wire intercom products. Products from older generations are not supported by this switch Maximum 2 entry panels per switch: A maximum of 2 VTO entry panels can be connected per switch. If there are more entry panels, they must be connected to the next switch. The switches can be interconnected. A maximum of 2 extensions per VTH indoor unit: A maximum of 2 extensions can be added to a VTH indoor unit. Should there be more extensions, it is recommended to connect the VTH with each other via a PoE switch. VTNS2003-B With 6 devices or less, a 48VDC power supply of 1.25A is sufficient. For 6 to 22 devices, a 48VDC power supply of 5A is recommended. Recommendations Recommended cabling: 4x0.5mm² with a maximum resistance of 4Ω per 100 meters. Maximum distance 50 meters 2x0.5mm² with a maximum resistance of 3.9Ω or less per 100meter. Maximum distance 50 meter UTP Cat5e 0.45mm with a maximum resistance of 12Ω per 100 meters. Maximum distance with 6 VTH is then 50 meters, with 12 VTH it is 30 meters. Slot control by external power supply: The power supply and control of locks and doors could in theory also be done from the switch. However, this may have a negative effect on the operation and mutual communication of the indoor and outdoor units and is therefore not recommended.
€119,00
-
Dahua VTO2202F-P-S2 outdoor station, IP and 2-wire, 160gr camera, PoE
VTO2202F-P-S2 outdoor station, IP and 2-wire, 160gr camera, PoE Dahua, door station, IP and 2-wire use, 2MP WDR camera with IR light, Mechanical button, Night vision & voice indicator, 160° angle of view. Power supply via 2-wire, front plate in aluminum alloy, IP55 & IK07, surface mount and flush mount box not included, power supply via 2wire or PoE. Exclusive in or surface mount or surface mount housing with rain hood, see related products below. The VTO2202F-P-S2 is an outdoor station from the new generation of Dahua Video Intercom products. The communication of this generation of video intercom products is over the SIP protocol. This protocol ensures a good speech-listening connection and offers possibilities for integration with third parties. The appearance of the outdoor unit is modernized, vandal-resistant and IP55. The VTO2202F-P-S2 is suitable for both IP and/or 3rd generation 2-wire Intercom products. The VTO2202F-P-S2 is compatible with all Dahua Video Intercom IP products starting with firmware version 4.3. Highlights: PoE: This intercom is PoE capable. This makes it possible to supply the module with power and network connection with one network cable. This then excludes power for the door lock. 2nd Door control from secure area with the DEE1010B: The DEE1010B is a module that can be connected to the main module via RS485. This allows additional contacts to be added to the VTO2202F-P-S2 system over a secure connection. The main connection on the module is the NO/NC relay. This can be used as a 2nd door controller. Suitable for PoE and 2-wire communication: The VTO2202F-P-S2 is suitable for IP technology with power over PoE and can combine it with 2-wire communication at the same time. Push notifications in DMSS app: It is possible to receive push notifications in the DMSS app. By adding the outdoor unit to the app. With this VTO an indoor unit is not necessary. Points of attention: H.265: By default, the video compression is set to H.265, however, some indoor stations only support H.264. The compression can be changed in the settings of the VTO Lighting: The name plate of the VTO is not illuminated, this makes the name plate less readable in the dark 3rd generation 2-wire cannot be used with 2nd generation 2-wire switches: The S2 models support 3rd generation 2-wire communication. This also means that they cannot be combined with the previous 2nd generation switches. On the basis of IP, these generations are compatible with each other. By connecting both switches based on IP, mutual communication is possible. Power supply for door lock not via PoE: Feeding a door lock requires an external power supply. Sealing: The front of the outdoor unit is IP65, the back still needs to be sealed off Messages/ Notifications in DMSS may be delayed: When the doorbell rings, notifications are sent directly from the entry panel so they generally arrive quickly. But they can also be delayed. This is influenced by various factors such as internet speed on the sending and receiving side, traffic on Dahua's cloud servers and the status of Apple's and Android's notification servers. External bell/buzzer only possible in combination with VTH:without an indoor unit, this outdoor unit cannot control an external doorbell Advices: Outdoor Installation: The intercom unit is IP65 and therefore suitable for outdoor installation. It is waterproof up to 12.5 liters per minute. However, this does require the back side to be completely sealed. Too much water can have a negative effect on the operation of the outdoor unit. It is therefore advised to exercise caution when installing the intercom in direct outdoor areas where wind and rain have free play. DMSS app and push notifications for multiple users: Be careful about the number of users who will work with the app and this intercom system. In any case, the recommendation is to use no more than 5 users per push button. Also, the module is not powerful enough to send video and audio data to a large number of users at the same time, Multiple Dahua Outposts: It is possible to use multiple and different entry panels in one system. However, please note that a maximum of 1 entry panel can serve as a SIP server. The rest will be secondary. Keep the firmware versions the same: As much as possible, try to work with equal firmware versions for the indoor and outdoor units. The latest firmware can be found with the product under tab downloads.
€249,00
-
Dahua VTO2202F-P-S2 Black, outdoor station, IP and 2-wire, 160gr camera, PoE
VTO2202F-P-S2 Black, outdoor unit, IP and 2-wire, 160gr camera, PoE Dahua, door station, IP and 2-wire use, 2MP WDR camera with IR light, Mechanical button, Night vision & voice indicator, 160° angle of view. Power supply via 2-wire, front plate in aluminum alloy, IP55 & IK07, surface mount and flush mount box not included, power supply via 2wire or PoE. Exclusive in or surface mount or surface mount housing with rain hood. Please see related products below; The VTO2202F-P-S2B is a black outdoor station from the new generation of Dahua Video Intercom products. The communication of this generation of video intercom products uses the SIP protocol. This protocol ensures a good speech-listening connection and offers possibilities for integration with third parties. The appearance of the outdoor unit is modernized, vandal-resistant and IP55. The VTO2202F-P-S2 is suitable for both IP and/or 3rd generation 2-wire Intercom products. The VTO2202F-P-S2 is compatible with all Dahua Video Intercom IP products starting with firmware version 4.3. Highlights: PoE: This intercom is PoE capable. This makes it possible to supply the module with power and network connection with one network cable. This then excludes power for the door lock. 2nd Door control from secure area with the DEE1010B: The DEE1010B is a module that can be connected to the main module via RS485. This allows additional contacts to be added to the VTO2202F-P-S2 system over a secure connection. The main connection on the module is the NO/NC relay. This can be used as a 2nd door controller. Suitable for PoE and 2-wire communication: The VTO2202F-P-S2 is suitable for IP technology with power over PoE and can combine it with 2-wire communication at the same time. Push notifications in DMSS app: It is possible to receive push notifications in the DMSS app. By adding the outdoor unit to the app. With this VTO an indoor unit is not necessary. Points of attention: H.265: By default, the video compression is set to H.265, however, some indoor stations only support H.264. The compression can be changed in the settings of the VTO Lighting: The name plate of the VTO is not illuminated, this makes the name plate less readable in the dark 3rd generation 2-wire cannot be used with 2nd generation 2-wire switches: The S2 models support 3rd generation 2-wire communication. This also means that they cannot be combined with the previous 2nd generation switches. On the basis of IP, these generations are compatible with each other. By connecting both switches based on IP, mutual communication is possible. Power supply for door lock not via PoE: Feeding a door lock requires an external power supply. Sealing: The front of the outdoor unit is IP65, the back still needs to be sealed off Messages/ Notifications in DMSS may be delayed: When the doorbell rings, notifications are sent directly from the entry panel so they generally arrive quickly. But they can also be delayed. This is influenced by various factors such as your Internet speed on the sending and receiving side, traffic on Dahua's cloud servers and the status of Apple's and Android's notification servers. External bell/buzzer only possible in combination with VTH:without an indoor unit, this outdoor unit cannot control an external doorbell Advices: Outdoor Installation: The intercom unit is IP65 and therefore suitable for outdoor installation. It is sprinkler-proof up to 12.5 liters per minute. However, the back of the unit must be completely sealed. Too much water can have a negative effect on the operation of the outdoor unit. It is therefore advised to exercise caution when installing the intercom in direct outdoor areas where wind and rain have free play. DMSS app and push notifications for multiple users: Be careful about the number of users who will work with the app and this intercom system. In any case, the recommendation is to use no more than 5 users per push button. Also, the module is not powerful enough to send video and audio data to a large number of users at the same time, Multiple Dahua Outposts: It is possible to use multiple and different entry panels in one system. However, please note that a maximum of 1 entry panel can serve as a SIP server. The rest will be secondary. Keep the firmware versions the same: As much as possible, try to work with equal firmware versions for the indoor and outdoor units. The latest firmware can be found with the product under tab downloads.
€249,00
-
Dahua VTO2211G-WP Outpost 2MP IP65, WiFi/PoE, Card Reader
Dahua VTO2211G-WP Outpost 2MP IP65, WiFi/PoE, Card Reader Full-HD 2MP camera with a 125° opening angle Mifare card reader up to 10,000 cards Suitable for PoE 2.4GHz Wi-Fi. Using the VTO2211 as a server while connected to Wi-Fi is not recommended. Suitable for surface mounting IP65 front (The back must be sealed for outdoor use) Suitable for use without indoor station Notice: without an indoor unit, this outdoor unit cannot control an external doorbell Points of attention: WiFi: This product is also suitable for WiFi. However, it is not recommended to use this outdoor station as a SIP server while connected to WiFi. This can be done but in case of signal problems it will work through in the entire intercom system. Our helpdesk offers support for problems related to the Intercom, however, our helpdesk does not offer support for Wi-Fi problems. Stand alone:This outpost can be applied standalone as a video doorbell. That means the outpost can be directly paired with the Dahua DMSS app. SIP ServerThe entry panel can also be used as a SIP server within an intercom system. However, it is not recommended to use the outdoor unit as a SIP server when it is connected to the Wifi. The entire intercom system is connected to the SIP server. If the signal, the available bandwidth or the stability of the Wifi is not satisfactory that gives problems in the entire intercom system. IP65:The specifications indicate that this device is IP65. This refers to the front side. The back must be cemented in outdoor applications. Outdoor installation:For Outdoor installation, we therefore recommend combining this product with the plastic VTM09R rain hood. This rain hood is made of plastic. Keep in mind that this can deform a bit on a non-level surface. It should also be glued on the back side. Proprietary audio files: An addition of the 4.5 firmware is the function to upload your own mp3 audio files. This allows you to play a personalized welcome text. Please note that these mp3 audio files can only be a maximum of 20kb. DMSS app with Push notifications: This outpost has an app. See our FAQ on how to set it up: DMSS with Push notifications for Dahua intercom Card reader: The outdoor station features a card reader suitable for Mifare. It is possible to add up to a maximum of 10,000 users. SD card slot: The SD card slot in the VTO has no function for the time being.
€199,00
-
Dahua VTO2311R-WP 2MP Villa Video Doorbell WiFi PoE/12volt
Ultra-slim design.PC and ABS material make it ideal for indoor and outdoor use.1/2.8″ 2-MP HD CMOS camera.Offers two-way video call as stand alone via the free Dahua App or with indoor monitors.Video and voice messages from visitors can be monitored on the indoor monitor.Video call and unlock via app.IR illumination and auto WDR.Wi-Fi connection.IP65 rated.H.264 and H.265.Unlocking with IC card.PoE or 12-33Volt DC power supply. Product Info
€249,00 €219,00
-
Dahua VTO3211D-P Video Intercom outdoor station with 1 push button, Mifare tag reader, PoE
Dahua VTO3211D-P Video Intercom outdoor unit with 1 push button The Dahua VTO3211D-P is a multi-functional intercom outdoor station. This intercom has 1 push button intended for one room. A very wide viewing angle of 140gr and proximity Mifare tag reader for remote door or gate opening. The VTO3211D-P is suitable for connecting to all types of Dahua VTH indoor units. (via network cabling and switch) To receive push notifications, a good stable network connection is required for both the outdoor unit and the smartphone.Please note that this intercom must be 12volt adapter powered or via a PoE adapter. Despite the IP65 specification, moisture in the microphone and/or speaker can adversely affect sound quality. Placing the outdoor unit in a position where water can directly enter the microphone or speaker is therefore not recommended. This outdoor unit must be linked to an internal unit.
€219,00
-
Dahua VTO3211D-P2 Video Intercom outdoor station with 2 push buttons, Mifare tag reader, PoE
Dahua VTO3211D-P2 Video Intercom outdoor station with 2 push buttons, Mifare tag reader, PoE The Dahua VTO3211D-P2 is a multi-functional intercom outdoor station. This intercom has 2 push buttons for example for 2 apartments or rooms. A very wide viewing angle of 140gr and proximity tag reader for remote door or gate opening. The VTO3211D-P2 is suitable for connecting to all types of Dahua VTH indoor units. (via network cabling and switch) To receive push notifications, a good stable network connection is required for both the outdoor unit and the smartphone.Please note that this intercom must be 12volt adapter powered or via a PoE adapter. Despite the IP65 specification, moisture in the microphone and/or speaker can adversely affect sound quality. Placing the outdoor unit in a position where water can directly enter the microphone or speaker is therefore not recommended. This outdoor unit must be linked to an internal unit.
€229,00
-
Dahua VTO3211D-P4 Video Intercom outpost with 4 push buttons, Mifare tag reader, PoE
Dahua VTO3211D-P4 Video Intercom outdoor station with 4 push buttons, Mifare tag reader, PoE The Dahua VTO3211D-P4 is a multi-functional intercom outdoor station. This intercom has 4 push buttons for 4 apartments or rooms, for example. A very wide viewing angle of 140gr and proximity tag reader for remote door or gate opening. The VTO3211D-P4 is suitable for connecting to all types of Dahua VTH indoor units. (via network cabling and switch) To receive push notifications, a good stable network connection is required for both the outdoor unit and the smartphone.Please note that this intercom must be 12volt adapter powered or via a PoE adapter. Despite the IP65 specification, moisture in the microphone and/or speaker can adversely affect sound quality. Placing the outdoor unit in a position where water can directly enter the microphone or speaker is therefore not recommended. This outdoor unit must be linked to an internal unit.
€249,00
-
Dahua VTO4202F-MB1 Single bell push button
VTO4202F-MB1 Single bell push buttonSingle bell push button for the Dahua intercom line. In beautiful silver colored luxury design.
€39,00
-
Dahua VTO4202F-MB2. 2-fold bell push
VTO4202F-MB2. 2-way doorbell2-way bell push for the Dahua intercom line. In beautiful silver luxury version.
€49,00
-
Dahua VTO4202F-MB5 5-way bell push button
VTO4202F-MB5 | 5-way bell push button |
€79,00 €59,00
-
Dahua VTO4202F-MF Fingerprint module
Fingerprint module for the Dahua intercom line. In beautiful silver luxury design.
€169,00 €139,00
-
Dahua VTO4202F-MK keyboard module
Keyboard Module for the Dahua intercom line. In beautiful silver luxury design.
€99,00
-
Dahua VTO4202F-ML Indicator Module
Indicator Module for the Dahua intercom line. In beautiful silver luxury design.
€49,00
-
Dahua VTO4202F-MN Blind plate
VTO4202F-MN Blank plateBlind plate for the Dahua intercom line. In beautiful silver luxury version.
€19,00
-
Dahua VTO4202F-MR Mifare card reader module
Mifare card reader for the Dahua intercom line. In beautiful silver luxury design.
€49,00
-
Dahua VTO4202F-MS Display Module
Display module for the Dahua intercom line. In beautiful silver luxury design.
€59,00
-
Dahua VTO4202F-P-S2 Video Intercom Camera Main Module
VTO4202F-P-S2 Video Intercom Camera Main ModuleNOTE ! The S2 models feature a new technology for 2-wire communication and cannot be connected directly to the VTNS1060A-2The Dahua VTO4202F-P-S2 is a 2 megapixel Full HD camera module for the 2nd generation Dahua modular IP video doorbell system. The camera module is a main module without a call button and can be connected and powered with a network cable or two wires. The VTO4202F-P-S2 must be combined with other modules.CapabilitiesThe camera has a very wide viewing angle of 168.6 degrees horizontally and has a 2 megapixel Full HD image sensor. The module is equipped with infrared LED light for good visibility in the dark. The VTO4202F-P-S2 features a microphone and speaker for clear video conversation via an indoor monitor or anywhere in the world using the app on your smartphone. The module can be connected to an electric lock or electric gate, for example, to remotely control a door or gate.The camera module only works together with an intercom indoor monitor and can additionally be used with the smartphone app. Thus, the VTO4202F-P-S2 cannot work stand alone without an intercom monitor and with only the app.Product Info
€249,00 €219,00
-
Dahua VTO4202FB-MB1 Single bell push button Black
Single bell push button for the Dahua intercom line. In beautiful black luxury design.
€39,00
-
Dahua VTO4202FB-MB2 2-fold bell push Black
2-way doorbell for the Dahua intercom line. In beautiful black luxury version.
€49,00
-
Dahua VTO4202FB-MB5 5-way bell push Black
5-way bell push for the Dahua intercom line. In beautiful black luxury version.
€59,00
-
Dahua VTO4202FB-MF Fingerprint module Black
Fingerprint module for the Dahua intercom line. In beautiful black luxury design.Product info
€129,00
-
Dahua VTO4202FB-MK keyboard module Black
Keyboard module for the Dahua intercom line. In beautiful black luxury design.
€99,00
-
Dahua VTO4202FB-ML Indicator module Black
Indicator module for the Dahua intercom line. In beautiful black luxury design.Product info
€49,00
I18n Error: Missing interpolation value "number1" for "You have seen {{ number1 }} out of {{ number2 }} products"